1500bar Marking Line Remove Hydro Blasting Machine

 

The hydro blasting machine for marking line cleaning is a professional equipment used to clean ground markings. It generates high-pressure water through a high-pressure pump. The high-pressure water is continuously transported to the cleaning device through a high-pressure hose and then sprayed from the ground at high speed. Where the cleaning device is pushed through, the high-pressure water flow is rotated to flush, so that the impact force of the water is greater than the adhesion between the marking paint and the road surface, so that the marking paint is separated from the road surface, achieving the purpose of cleaning. Moreover, this pure high-pressure water physical cleaning method does not require the addition of any chemical agents when used, is pollution-free, and will not damage the ground.

 

The principle of the road marking removal high-pressure jetting machine is to continuously input the ultra-high pressure water flow generated by the high-pressure cleaning machine into the hand-push cleaning machine through a high-pressure hose, and then spray it on the road surface at high speed. The water pressure can reach 1500bar. Wherever the hand-push cleaning machine is pushed, the road surface will be intact after the rotation and flushing of the high-pressure water flow, and the road markings will be cleaned by the road marking remover.

 

In recent years, ultra-high pressure cleaning machines have gradually developed, and ultra-high pressure water jet technology is currently a very effective road marking removal process. Commonly used traditional road marking removal methods are divided into manual cleaning, chemical cleaning and mechanical cleaning. Although these traditional road marking removal methods can remove the markings cleanly, they will damage the road surface, affect the road landscape, and increase the cost of road maintenance. Therefore, it is very important to choose the appropriate road marking removal method according to the degree of impact on traffic, the required operation time and the degree of impact on the environment.

 

 

Water blasting quickly removes markings faster and more thoroughly than abrasive methods. This method will not damage the pavement or asphalt of the road . Water blasting -hydro blasting is fast and productive, and avoids exposing the environment to chemicals or contaminants. lt also simplifies clean up, is dustless and leaves a clean surface.

 

Ultra-high pressure cleaning machines have become the leading equipment for industrial cleaning in the world. Ultra-hydro blasting machines use the impact force, shear force and other factors of ultra-high pressure water jets to act on the surface of the markings, destroying the structure and state of the markings, thereby achieving the effect of clearing the marking layer. The key technologies for water jet marking removal are the development of ultra-high pressure pump units and the analysis of the marking removal mechanism and influencing factors. In the operation of clearing traffic signs, different water jet pressures, moving speeds, etc. should be used according to the actual thickness of the markings, so as to achieve better cleaning efficiency and effect.

 

The cleaning effect should not only refer to the cleaning quality, but also consider the cleaning efficiency. The cleaning effect of road marking lines mainly depends on four aspects: jet pressure, actuator movement speed, target distance, and rotary joint speed. Only by mastering the factors that affect ultra-high pressure water cleaning equipment can we achieve twice the result with half the effort in actual use, and truly make ultra-high pressure cleaning machines give full play to their advantages of wide cleaning range, low cost, high efficiency, good quality, water saving and environmental protection in industrial cleaning.

The ultra-high pressure water flow generated by the high-pressure cleaning machine is continuously input into the hand-push cleaning machine through the high-pressure hose, and then sprayed at high speed on the road surface. The water pressure can reach 1500bar. Where the hand-push device is pushed, the road surface is intact after the rotational flushing of the high-pressure water flow, and the painted marking lines on the road are cleaned cleanly by the road marking remover.

 

Features of the Hand-push device:

1. The cart is equipped with a height adjustment device, which can adjust the height of the rotating head at will for easy use.

2. The cleaning car is designed with a remote control switch, which can remotely control the switching of high and low pressure working states

3. The rotating mechanism adopts an original design and can support a high pressure of 1500 kg.

4 The rotating head can clean up to 200mm in width and faster in cleaning speed.

5. The rotating head is equipped with a circular protective device, and a suction device can be added to ensure the cleanliness of the work site.

 

 

	GYB-5 1500/85
	366 rpm
	Pump speed:366rpm
	Plunger stock:120mm
	1500 bar / 22000 psi
	85 L/min
	22mm
	160kw, 3Phase, 380v/50Hz or 440v/60Hz
	225kw, 6-cylinder

 

 

 

 

 

 

 

 

 

 

1. Packing: Plywood packing

2. Shipping way: suggest deliver by sea

3. Delivery port: Qingdao Port; or deliver to any port you need

 

 

Népszerű tags: 1500bar marking line remove hydro blasting machine, China 1500bar marking line remove hydro blasting machine suppliers, factory